Screw - Self-Tapping Phillips Head - 8-18" x 3/4"

See what our Experts say about this Flint Hill Goods Accessories and Parts

• How To Mount the Optronics LED Clearance or Side Marker Light w/ Reflex Reflector Part # MCL31AB
  The Optronics LED Clearance or Side Marker Light w/ Reflex Reflector part # MCL31AB mounts by running two screws like part # 1131832 though the base. In order to access these screw holes you will need to remove the lens. I have attached a photo that shows the screw holes. I have also attached an install video for you as well. In order to make the wiring connections you will also need part # DW05714 and part # DW05737-1.
  view full answer...
  
• Replacement for Reflect-O-Lite 400
  The Reflect-O-Lite line has been discontinued for quite some time so replacements are no longer available. However, the Trailer Clearance or Side Marker Light w/ Reflex Reflector part # MC32AB is a very similar option that will work well in its place. In regards to installation, all you will need to do is mount the base with a screws part # 1131832 and then match up the wires with butt connectors part # DW05744-5.
  view full answer...
• Replacement Trailer Clearance Lights for Bargman 99 Series
  The correct replacement trailer clearance light for a Bargman 99 Series is the Optronics Trailer Clearance or Side Marker Light part # MC44RB for red or part # MC44AB or amber. The mounting holes for this light are spaced 3" apart on center. It features a simple two wire installation, one for power and one for ground. In order to remove the old lights it would be easiest to just drill out the rivets with a small drill bit. The drilled holes would then make good pilots for the self tapping...
  view full answer...
• Does the Plunger and Nylon Socket Door Holder DH605 Come with Install Hardware
  The Plunger and Nylon Socket Door Holder part # DH605 does not come with installation hardware but we do have screws that will work for this, the part # 1131832.
  view full answer...
• How Should the Thinline Trailer Reflectors with Adhesive Backing Be Installed
  Yes. It's not uncommon that over time, adhesives are affected by heat, humidity and exposure to the sun and UV rays; the Thinline Trailer Reflectors - Adhesive Backing - Screw Mount - Rectangle - Amber - Qty 2 # RE15AK aren't immune to this, unfortunately. However, when installing these I typically don't recommend relying only on the adhesive backing and that you also use a self tapping screw like the Screw - Self-Tapping Phillips Head - 8 x 3/4" # 1131832 to keep them firmly attached to...
  view full answer...
  
• Does the Hot-Line LED Third Brake Light Come With Mounting Hardware
  The Hot-Line LED Third Brake Light for Trailers part # 328-003-84R does not come with mounting hardware but all you will need for this is two screws, part # 1131832.
  view full answer...
• Can the Horse Trailer Breast Pad Be Attached Directly to Metal
  The Horse Trailer Breast Pad part # HTP24BK could easily be attached to a metal divider using self tapping screws like part # 1131832. I would agree that generally speaking the breast pads are attached to plywood but I don't see an issue attaching them to metal either.
  view full answer...
• Access Door Measurement for Compatibility With 2017 Jayco Precept 31UL Motorhome
  The Ultra-Fab Universal Access Door for Trailers and RVs - 5" x 5" Opening - Chrome # UF48-979010 has overall dimensions that are 8 inches wide by 7 inches tall. The best thing you can do is look at the attached diagram of screw center locations to see how they match up to your 2017 Jayco Precept motorhome. If the holes don't match up but are a larger pattern, then you will be able to install the cover with self tapping screws like # 1131832 into the side of your motorhome.
  view full answer...
  
• Recommended Door Holder for Fender Mounting
  The Plastic Stem and Rubber Socket Door Holder - 2" Long Stem # DH39R can be installed onto your fender if desired to allow your door to be secured open. You can alternatively use a Hook and Keeper for Enclosed Trailer Door # 383400 in another location like mounted to the fender to give you a similar option. There is not an option we carry that is long enough to allow connection to the main trailer wall when the fender is making contact with the door.
  view full answer...
• RV Slide-Out Topper Mounting Hardware
  The Replacement Mounting Hardware for Lippert Solera Slide Topper - Black # LC701665 will help you get the parts you are missing.
  view full answer...
• Why Are the Holes On the Back of the Automatic Changeover RV LP Gas Regulator Not Threaded
  Yes, you will need to use self-tapping screws like part # 1131832, not bolts which will form their own threads when mounting the Automatic Changeover RV LP Gas Regulator part # 37207-30395.
  view full answer...
• How To Mount the LED Trailer Clearance or Side Marker Light MCL32AB
  The Self-Tapping Phillips Head Screw part # 1131832 can be used to secure the LED Trailer Clearance or Side Marker Light part # MCL32AB. This light will require two screws per side. If you also need wiring connectors we have those as well, the Deka Heat Shrink Butt Connector part # DW05743-5.
  view full answer...
• Recommended Light for RV Storage Compartment
  The LED Utility Light with Switch part # 328-001-504E is my recommendation for a storage compartment light as it is battery powered so you don't have to worry about routing wires to the storage compartment which can be a huge hassle. The battery will also last a long time as the LED's draw very little power so you won't have to worry about changing out the battery frequently. In order to install the light you just simply remove the lens, mount the base with screws like part # 1131832,...
  view full answer...
• What Hardware Is Needed To Install the Thinline LED Trailer Clearance or Side Marker Light MCL67AB
  The Thinline LED Trailer Clearance or Side Marker Light part # MCL67AB is a surface mount light that has two mounting holes which you will see once the lens is removed. In order to mount this you can use pretty much any self tapping-screw like the Self-Tapping Phillips Head Screw part # 1131832. The Self-Tapping Phillips Head Screw could be used to mount most of our trailer side marker/clearance lights.
  view full answer...
• Hardware Needed For LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen
  The LaSalle Bristol CrossBreeze Adjustable Toy Hauler Screen - 92" Wide Item # 3441409200PBK just requires some self tapping screws like Screw - Self-Tapping Phillips Head - 8 x 3/4" Item # 1131832.
  view full answer...
• What Size Screw Is Needed for the Bargman Trailer Light 30-68-510
  The Bargman Trailer Clearance or Side Marker Light 30-68-510 or Optronics Trailer Clearance or Side Marker Light part # MC48RB do not come with mounting screws therefore there is not an exact size recommend for this. That said, the screw will just need to be small enough to fit in the hole and long enough to secure both the lens and base. I really wish I had an exact size for you but the Self-Tapping Phillips Head part # 1131832 should work.
  view full answer...
• Replacement Clearance Light Lens for a 1989 Beaver Motorhome
  The task of finding replacement lens covers for a now 30+ year old motorhome is going to be very difficult. We do not have the correct replacement lens covers you need and you are going to have a very hard time finding them. Therefore, I recommend just replacing them as the process to install clearance lights is very easy and straightforward. All you will need is some butt connectors and a few mounting screws if they are not already included with the light. I have attached a list of our...
  view full answer...
• How to Install Side Marker Light
  To install a side marker light like the Optronics # AL82AB on your 2014 Malibu you will need to ground the white wire and then connect the black wire to your running light circuit. This then installs on the mounting bracket # A91BOB which you will need install using something like a self-tapping screw # 1131832. Sometimes the lights ground via the mounting hardware so if that's the type of light you have you need to make sure that you mount it to a clean, bare-metal surface. Attached...
  view full answer...
  
• Hardware for Tekonsha Mounting Kit # 5280
  The Mounting Bracket # 5280 for your Envoy brake controller does not include the mounting hardware and Tekonsha does not provide this. To mount the bracket all you need are some 3/8 inch screws like # 1131832. You can also just obtain some at a local hardware store if that is easier. The holes on the bracket will match up to the mounting hole pattern on your Envoy.
  view full answer...
• Mounting Hardware for Optronics Mounting Bracket
  The Optronics Mounting Bracket # A91CB grounds through the mounting hardware. So whatever hardware you use, whether screws or pop rivets, make sure it's made of a conductive metal. The hardware we generally recommend is self-tapping screws # 1131832 but pop rivets should work just fine.
  view full answer...
• How To Attach the Black Molded Fender Bracket A67BB
  In order to attach the Black Molded Fender Bracket part # A67BB I recommend using the Self-Tapping Phillips Head Screw part # 1131832 because the head will sit closer to the base and will allow for the Optronics Thinline LED Trailer Fender Light part # MCL65ARB to sit flush. The Black Molded Fender Bracket we offer grounds via the mounting hardware so a ground wire is not present but if you have a version of this bracket that does have a ground wire then you can just snip this and tape...
  view full answer...
• Can a Heat Shield be Sandwiched Between the Frame and Trailer Hitch
  The Curt Trailer Hitch Receiver part # C12111 on your 2017 Ford Escape will need to be attached directly to the frame without anything between it. Sandwiching the heat shield between the frame and hitch will affect the integrity of the hitch and void Curt's warranty. Therefore, I cannot recommend you sandwich the heat shield between the frame and the trailer hitch. In order to further secure the heat shield onto the body of your Escape, you can always use a few self tapping screws like...
  view full answer...
• Will LED Clearance Light Work With One Wire
  Yes, the Thinline LED Clearance and Side Marker Light - Submersible # AL91AB will work with your single power wire, as it uses a 2-wire (one for power, one for ground) pigtail or 1-wire pigtail with a self-grounding bracket. To mount this light you have a couple options. The first is the Mounting Bracket # A91BOB with Right Angle 2-Wire Pigtail # A46PB; you'd also want to use the Self-Tapping Screw # 1131832. Your other option to mount this light is to use Self-Grounding Mounting Bracket...
  view full answer...
  
• How To Install the Optronics Thinline LED Trailer Fender Light
  The Optronics Thinline LED Trailer Fender Light part # MCL67ARB comes with a mounting bracket so as long as the surface you will be installing it on is metal then yes, it will work for you. All you would need to do to install the light is use two self tapping screws like part # 1131832 to mount the base and then once this is done you can attach the light to the base. To complete the process you will then need to attach the black wire to the running light circuit on your trailer which is...
  view full answer...

Do you have a question about this Accessories and Part?